How To Recone A Subwoofer | Easy Steps

Many people are wondering how to recone a subwoofer. If you are one of these people, then you have come to the right place! We will discuss how to do this in detail to decide whether or not this is something that you want to try.

This article covers all aspects of how to recone a subwoofer, from what tools and supplies are needed, how much work is involved and even provides some helpful tips for getting started with this task.

So, are you ready? Let’s get started!

How To Recone A Subwoofer by

What Tools And Supplies Are Needed For Recone Subwoofers?

  • Subwoofer
  • Supplies (canvas, glue)
  • Tools (screwdriver, pliers)
  • Enclosure
How To Recone A Subwoofer by

5 Steps To Recone A Subwoofer

1. Verify That You Have The Correct Replacement Cone

How To Recone A Subwoofer by

It should be compatible with your speaker system and not too large or small to fit properly.

If this doesn’t match up correctly, then the subwoofer will perform poorly and may even damage itself in some other way as well. If this happens, don’t worry, you can always contact the manufacturer.

2. Disassemble The Subwoofer

How To Recone A Subwoofer by

Remove screws holding the speaker together, take off magnet and basket using a screwdriver or another tool you have access to.

It is extremely important not to damage anything during this process. It can lead to further complications later on if something is damaged during disassembly that should not have been. The same goes for reassembly too.

Remove the speaker cone by pulling it away from the voice coil and popping off glue holding them together.

It is essential not to damage any of the components while removing them, as this can lead to further complications later on if something is damaged during disassembly that should not have been or damages caused cannot be fixed without replacing something else as well.

3. Prepare The New Speaker Cone

How To Recone A Subwoofer by

Before applying glue to the voice coil, you need to make sure that your replacement cone is in good condition and free of cracks and chips.

If there are problems with this, then do not apply glue at all because it can create further issues down the road if something goes wrong when glueing it back together. It would be best to find a replacement for this part before continuing with the process at all if you notice any problems like this.

If there are no problems with the cone, then apply a small amount of glue to the backside to make contact with the voice coil.

Be sure to apply a thin layer of glue, as too much can create problems later on when it is time for the speaker cone to go back over the voice coil.

Carefully place your replacement speaker cone onto the voice coil and press down firmly so that it makes good contact.

Be careful not to damage anything here because any problem that occurs will have an effect on the overall performance of your speaker system.

4. Reassemble Your Subwoofer

How To Recone A Subwoofer by

First, place the basket and magnet back onto the speaker in their original order and secure them into position using screws or other parts that were used to hold them together before you disassembled it earlier on.

Be sure not to damage anything here! If something is damaged during reassembly without realizing it, then this can lead to further complications down the road, which you will have a more challenging time fixing.

Next, place your speaker cone over top of the voice coil and secure it into position using glue or other adhesives that were used during disassembly before putting everything back together again.

Be careful not to damage anything here because any problem that occurs will affect the overall performance of your speaker system.

Once this is done, it’s time to put everything back together again using all the parts you took off before.

Carefully thread screws back into place or screw everything else together as it was when you were taking it apart.

5. Test It Out

How To Recone A Subwoofer by

Once everything is put back together again, turn on your subwoofer and test to make sure that the cone moves freely without any problems or sounds like anything other than what you would expect it to sound like.

If there are no issues here, then congratulations! Your speaker system should now be fully functional once more and should run as good, if not better, than it did before you began the repair process.

If problems are found during this step or other issues that develop later on, you need to disassemble everything again and check for any mistakes made at one of these steps because something went wrong here. This could be due to an error in reassembly or may have occurred during the process of disassembly.

If things go well, you can now put your subwoofer back where it belongs inside your entertainment system so that you can get back to enjoying it.

Why Do I Need To Recone My Subwoofer

A subwoofer may need to be reconed for a variety of reasons, but typically, it would be necessary to have the cone repaired due to some damage.

This could occur due to something like one of your kids or pets knocking it over, but this is also possible because subwoofers can accumulate dust over time which builds up and causes damage to the speaker.

Some people have also been known to actually do this on purpose to change the sound of their subwoofer just for fun, but this is not recommended because it can be dangerous.

It is also possible that the voice coil somehow came into contact with something during this process, which could potentially cause some damage to it.

Tips For Using The Best Speaker Cables With Your New Recones

The best place to get speaker cables is somewhere that has a good reputation for providing high-quality products at reasonable prices. The most common types of speaker cables are the ones with copper wires inside of them, but some people also use speaker cables made out of silver or gold instead.

The most important thing to do is find a store that has speaker cables available and then compare their prices with those of other stores in your area.

Another thing you should consider when buying speakers cables is how long they are because this will determine if it’s possible for you to run them from where your subwoofer or amplifier sits all the way up to where your speakers are.

If you’re not sure whether or not the cables you have will be long enough, then it is best to buy a slightly longer set than you think you might need, just in case.

Next, it’s essential to look and see if the speaker cables you have come with any extra features included.

For example, some speaker cables might come with a unique design that allows them to be easily hidden away, which can be helpful if you don’t want them to be visible.

How To Recone A Subwoofer by